The IC-V200T VHF Radio Module and H16 Super Eprom

March 16 , 2016

The documentation that follows applies only to the IC-V200T modem whose ISS was deleted.

"

Possibility of EPROM H16

  • Remove the access code (Dealer)
  • Set of 80 memory channels (instead of 10) from 00 to 79
  • Direct recall 00 to 09 channels
  • Permanent display of the frequency instead of selective.
  • Programming limit band .... I have 144,500 to 146.000Mhz.
  • Sending a selective calling (1747Hz for relays)
  • Selection of 12,5 - 25 - 37.5 - 50kHz.
  • Reverse (rotational frequency Tx / Rx and the shift.)
  • Call for the "monitor" to edit data in RAM
  • Display the software version.
  • Choice in scanning: either the channel or memory portion of the previously defined frequency

The eprom

If you currently have or EPROM must enter the code to get to the DEALER for programming, remove it.

Set a new 27C256 with the content you find at the bottom of this page.

Before putting the new Eprom on the carrier, "pump" little welding which is just next to the lithium battery.

This will effectively clear the contents of RAM.
Wait a few seconds and then repeated the strap.
Turn the Eprom Version Super H16.
Turn on the Tx, the display should then indicate CLEAR 00 (This is the No. 1 channel).
LCI is now re-initialized.
I found that the 80 channels is 00 to 79 was initialized on frequency 145,000 MHz simplex

Action Buttons

Programming the frequency of a channel!

  • Two Cases

For traffic simplex
OrderingLcd display
Ignition txSuper H16
Pressing "CH"- - (2 dashes flashing)
Type "00" (zero 2 times)145000 (or other)

You're on channel 0.
We must now return frequency.
OrderingLcd display
Pressing "SET"The 1st digit blinks.
Type "1"The 2nd digit blinks
Type "4"The 3rd digit blinks
Type "5"The 4th digit blinks
Type "5"The 5th digit blinks
Type "0"The QRG of 145,500 returned

The last "0" (zero) frequency will be returned automatically.
In this case the first QRG = TX is that of RX.
In fact, the frequency returned is the receiving and there was no shift of definition, that of emissions will be identical.
If you made a mistake while entering the QRG, know that pressing the "CLR" allows you to reverse a correct figure.

To relay traffic
OrderingLcd display
Ignition txSuper H16
Pressing "CH"- - (2 dashes flashing)
Type "01" (zero 2 times)145000 (or other)

You are now on the channel "01".
Therefore enter the receive frequency and then SHIFT.
OrderingLcd display
Pressing "SET"The 1st digit blinks.
Type "1"The 2nd digit blinks
Type "4"The 3rd digit blinks
Type "5"The 4th digit blinks
Type "6"The 5th digit blinks
Type "0"The QRG of 145,600 returned

The last "0" (zero) frequency will be returned automatically.
For info:
when you type the QRG 14572 of .725 for the 5 will be added.
Also for the frequency of 145.712.5 2 will automatically be displayed

It must now return to the SHIFT input relay.
OrderingLcd displayComment
Pressing "then CH SET"SH | - 000000The sign flashes orange
Type "CLR"SH - 000000Shift for NEGATIVE
Or "G"SH | - 000000to shift position
Type "0" 0 00000The figure is back in Italic
Type "0" 0 0 0000Comment
Type "0" 00 0 000Comment
Enter "6"000 6 00Comment
Type "0" 0006 0 0Comment
Type "0" 00060 0 Comment

If the programming was successful, the ICV shows: 01 145600
If you wish to see the QRG Issue is simple according to the table below:

Reverse function
OrderingLcd displayComment
01 145600Display start
Pressing "CH"--Left of the dash flashes
then "CLR"01 145600You see the QRG Emission
Type "CH"--Left of the dash flashes
then "CLR"01 145600You are back to normal

To trigger a VHF on our territory we need to send a tone near 1750 Hz tone ..... This is managed by a board of my design and implemented in hardware
We will leave the channel "01" since it is the relay in house

Sending the relay tone
The Evoia this tone, and the shift in transmission will be performed by the support of the "CALL" You press the button a few seconds to put the V200 in transmission, and automatically share the tone .. When you release the tx dinner reception mode, and the relay you want to open should be triggered.
OrderingLcd displayComment
Pressing "TONE"E 123.r4.rA5
then "1"0. F FFFFFFThe F point after flashing
Press "CLR"0. FFFFFFFThis is the 0 point to the flashing
Type "8"8. F FFFFFF1 F flashing
Type again "8"FFFFF 8.8 FIt follows that the F is flashing
6 times and then "G"8.8FFFFFFFinal format (Key G = F)
01 145600You return to the normal view

If an error occurs during programming you can go back thanks to the "CLR"

Programming band limits
The following allows many different frequencies and Mini Maxi for scanning
OrderingLcd displayComment
Press CH-- Left of the dash flashes
Then GLF x xxxxx the 1st digit blinks
Type 1LF 1 x xxxxthe 2nd digit blinks
Type 4LF 14 x xxxthe 3rd digit blinks
Type 4LF 144 x xxthe 4th digit blinks
Type 5LF 1445 x xthe 5th digit blinks
Type 0LF 144500 The low frequency 144500 returned
Step 2 .... Upper limit
HF x xxxxx the 1st digit blinks
Type 1HF 1 x xxxxthe 2nd digit blinks
Type 4HF 14 x xxxthe 3rd digit blinks
Type 6HF 146 x xxthe 4th digit blinks
Type 0HF 1460 x xthe 5th digit blinks
Type 0HF 146000 146,000 high frequency is back

Scanning the defined band portion.
Here is the method to run the scanner on the portion of tape bounded.
OrderingLcd displayComment
Ignition of Tx Super H16 Display start
Press CH -- Left of the dash flashes
than SCAN Mod -- the dash to the right of MOD flashes
if you type 0 Mod 0 Scan start / stop on a carrier but does not leave
if you type 1 Mod 1 Scan start / stop on a carrier and again after 2s release channel
if you type 2 Mod 2 Scan start / stop during 4s and again even if a carrier is always present
if you type 3 Mod 3 Scan start / stop during repart 8s and even if a carrier is always present
if you type 4 Mod 4 Scan start / stop during 12s and again even if a carrier is always present
if you type 5 Mod 5 Scan start / stop during 16s and again even if a carrier is always present
if you type 6 Mod 6 Scan start / stop during 20s and again even if a carrier is always present
if you type 7 Mod 7 Scan start / stop during 24s and again even if a carrier is always present
if you type 8 Mod 8 Scan start / stop during 28s and again even if a carrier is always present

Scanning with automatic presetting.
It is possible to automatically memory frequencies on which the Sanner stops.
Here is the method.
OrderingLcd displayComment
Ignition of Tx Super H16 Display start
Press CH-- Left of the dash flashes
than SCAN Mod -- the dash to the right of MOD flashes
type 9 Mod 9 Scan start / stop on station and is in memory from the channel 60 and then again

At the next stop on a station, the memory will be made on the 61 channels .... and so on until 79.

Scanning of your favorite channels.
You can if you want to scan only certain channels, with the possibility of multiple "banks".
For example in the 1st bank to place only channels "Relay" and in the 2nd bank of frequencies "Packet"

This requires at least 2 channels expressed in the scanner, otherwise it does not work.

For example the selected channels:
Channel: 46 QRG: 145.600.0
channel: 50 QRG: 145.650.0
channel: 51 QRG: 145.662.5
Channel: 55 QRG: 145.712.5
Channel: 58 QRG: 145.750.0

That's the "Relais".

Now, some frequencies "Packet"

channel: 24 QRG: 144.800.0
channel: 29 QRG: 144.950.0
channel: 32 QRG: 145.275.0

We therefore have 2 banks to be programmed.

How to program all this?
OrderingLcd displayComment
Ignition of Tx Super H16 Display start
The tx is on 01 144500 The channel at the time of ignition (eg)
Press CH - - 144500 left of the dash flashes
Type 4 4 - 144500 The 1st number is returned, the 2nd dash flashes
Type 6 46 145600 The 2nd number is returned, the QRG of 145,600 appears.
You are therefore 46 145600 The channel 46, frequency 145,600
Type TONE E 123.r4.rA5 The response of tx
Then 0 SALT 00 1 0 blinks
Type 0 SALT 00 Zero is left retracted, the 2nd 0 (Zero) blinks
Enter 1 SALT 01
The tx afiche 46 145600 The first frequency is stored in bank 1
Repeat for the following QRG Up to 145,750

To start scanning the channels 46, 50, 51, 55 and 58, press the "SCAN".
Choose the mode (0 to 8).
Tx meets the "SEL 00"
Answer "01"

It will do the same manipulation for channels "Packet", but instead of returning "SEL 01" will require "SEL 02.

To scan channels packet, the command is:
Touch "SCAN"
Tx meets the "MOD -"
Reply by 0 to 8 (depending on the time of arrest on the channel)
The tx now indicates "SEL 00" Enter "02"
The tx scans the channels, 24, 29 and 32 (packet).

You can prepare several banks according to your choice and can scan what you want.

To return to the scanner "Normal", simply enter "SEL 00" on application. At this point, you scan all channels of the Tx from 00 to 79.

Direct access to a channel programmed into memory other than 0 to 9.
OrderingLcd displayComment
Ignition of Tx Super H16 Display start
Press CH - -- left of the dash flashes
Type 7 - --left of the dash flashes
Type 0 70 You are on channel 70

The RESET button
The RESET button allows you to close or open the audio. (BF rx).
When the BF is in operation a small icon "HP" appears on the screen.

Direct Access channels 0 to 9
When you have programmed the memory from 00 to 09, you remember them at the push of channel number for access.

No programming
You can not choose between a 12.5 - 25 - 37.5 or 50kHz.
The table below shows you how:
OrderingLcd displayComment
Type TONE E 123.r4.fA5
then SET NO x display Not
type 1 to 12.5 kHz STEP 1 The step of 12.5 KHz is returned
or
type 2 to 25khz STEP 2 The 25khz not returned in
or
type 3 for 37.5khz STEP 3 The not in back 37.5Khz
or
type 4 to 50kHz STEP 4 The 50kHz not returned in

Cloning Transmission
The function of cloning issue can be activated by TONE + CLR fontion

Cloning Reception
To enable cloning desk must press SCAN and press the small switch which is under the hood later Loudspeaker.

Calling the monitor function
To change the contents of the RAM type CH + 9 Attention does not tinker in RAM if you do not know the addresses and especially the content ....

The beep of the keyboard
CH + CH enables or disables the beep of the keyboard ....
(Does not work on some versions.)

Show software version
CALL CH + provides the software
After 3 seconds, the display returns to normal.

Programming CTCSS Emission
TONE + 6 for the return value of CTCSS
To fall off the CTCSS, you must enter the value "00".
Below is the table of CTCSS tones.
Your No.Frequency (Hz)Data (Hex)
167,03E
271,93D
374,41B
477,03C
579,719
682,53B
785,417
888,53A
991,515
1094,839
11100,038
12103,537
13107,236
14110,935
15114,834
16118,833
17123,032
18127,331
19131,830
Your No.Frequency (Hz)Data (Hex)
20136,52F
21141,32E
22146,22D
23151,42C
24156,72B
25162,22A
26167,929
27173,828
28179,927
29186,226
30192,825
31203,524
32210,723
33218,122
34225,721
35233,620
36241,81F
37250,31E

Forward and backward channel
G down one channel
CLR rises channel
Tx must be on a channel to any manipulation.
Example:
you turn on the tx, it is about 15 times ..... press CLR 1 it goes to 16 .....
press 2 times G is about 14..

Software download eeprom ic-v200t.bin